Delfield N8600 Specifications download pdf (Page 11)

N8000 Series Drop-In Installation and Operation Manual

For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.deleld.com

Installation

N8000, N8000N, N8000-R, N8100B, N8100NB, N8100-BR, N8200, N8200-ST, N8200G, N8100-FA & 8100-EF

These units are intended for indoor use only. A room

temperature of no more than 86°F (30°C) is recommended.

Be sure the location chosen has a counter strong enough to

support the total weight of the unit and contents. A fully loaded

model may weigh as much as 600 pounds! Reinforce the

counter as necessary to provide maximum loading.

Unit requires that the sides and bottom are not

any closer than 3” (7.6cm) to any combustible

material.

The counter cut-out sizes and power requirements are shown

on the specication pages. A gasket is installed in the ange

of each unit. The weight of the unit on the gasket forms a seal

preventing liquids from seeping into the cut-out opening.

Louvers

Self-contained refrigerated units (N8100, N8100NB, N8100-BR,

N8200, N8200-ST and N8200G Series) require airow to the

compressor. A 13” x 25” (33 cm x 63.5 cm) louver is provided

by Deleld and must be installed in the counter in front of the

condenser. The louver cutout dimension is 11” x 22” (27.9 cm

x 55.9 cm). The rear must have an opening to permit removal

of heated air. The opening must be at least 8” x 11”, a total of

88 square inches (20.3 cm x 27.9 cm, a total of 566 square

centimeters).

Plumbing

The units drain must have an outlet to an appropriate drainage

area or container. A drain trap must be installed. N8200 and

N8200-ST series have 1/2” drain and N8200G series have 3/4”

drain located on end/center. The 1” diameter drain on N8000,

N8000-R, N8100, N8100NB, N8100-BR, N8100-FA and 8100-

EF Series units is shipped loose and must be connected during

installation. N8157-FA, N8169-FA, and N8182-FA have two

drains.

Moisture collecting from improper drainage

can create a slippery surface on the oor

and a hazard to employees. It is the owner’s

responsibility to provide a container or outlet

for drainage.

Some N8000, N8000N, N8000-R, N8100B,

N8100NB and N8100-BR may have polyethylene

insulation in the drain hole. This can easily be

cut out without any contact or damage to the

units interior insulation or refrigeration lines.

Electrical connection

Refer to the amperage data on the specication pages, the

serial tag or your local code to be sure the unit is connected

to the proper power source. A protected circuit of the correct

voltage and amperage must be run for con nec tion of the line

cord.

Some units have an ON/OFF switch located behind the

louvered panel in the machine compartment. Simply turn the

switch to ON to begin operation.

Some units have an OFF position on the thermostat dial

which is located behind the louvered panel in the machine

compartment. Simply turn the dial to begin operation.

The unit must be disconnected from the

power source whenever performing service or

maintenance functions.

Never operate the unit without the louvered

panel in place!

CAUTION

DANGER

Installation N8600

These units are intended for indoor use only. A room temperature

of no more than 86°F (30°C) is recommended. Be sure the

location chosen has a counter strong enough to support the

total weight of the unit and contents. A fully loaded model

may weigh as much as 600 pounds! Reinforce the counter as

necessary to provide for maximum loading.

Unit requires that the sides and bottom are not

any closer than 3” (7.6cm) to any combustible

material.

The counter cut-out sizes and power requirements are shown

on the specication pages. A gasket is installed in the ange

of each unit. The weight of the unit on the gasket forms a seal

preventing liquids from seeping into the cut-out opening.

The cut-out dimensions for the control box on N8600 Series

units is 4.25” x 12.25” (10.8 cm x 31.1 cm).

Louvers

For proper refrigerated operation, N8600 Series units require

airow to the compressor. A 13” x 25” louver is (33.0 cm x 63.5

cm) is provided by Deleld and must be installed in the counter

in front of the condenser. The louver cutout dimension is 11”

x 22” (27.9 cm x 55.9 cm). The rear must have an opening to

permit removal of heated air. The opening must be at least 8” x

11”, a total of 88 square inches (20.3 cm x 27.9 cm, a total of 566

square centimeters).

Plumbing

The units 1” (2.54cm) drain must have an outlet to an appropriate

drainage area or container.

Moisture collecting from improper drainage

can create a slippery surface on the oor

and a hazard to employees. It is the owner’s

responsibility to provide a container or outlet

for drainage.

Electrical connection

Refer to the amperage data on the specication pages, the

serial tag or your local code to be sure the unit is connected to

the proper power source.

The unit must be disconnected from the

power source whenever performing service

or maintenance functions.

Never operate the unit without the louvered

panel in place!

CAUTION

DANGER

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 35 36

Comments to this Manuals

No comments

Delfield N8600 Specifications Page 11

Comments to this Manuals

Related products and manuals for Unknown Delfield N8600